lexcarb ![](0logo.gif) **[rexresearch.com](../index.htm)** --- **Marit JAGTOYEN** **Auto Exhaust Water Recovery System** --- [**http://lexcarb.com**](http://lexcarb.com) **Development of On-Board Water Recovery Unit for the Future Combat System (FCS), HMMWV and the Tactical Quiet Generator** **Executive Summary** The primary goal is to develop a fully integrated and automated prototype system for the collection, purification and storage of potable water from the exhaust gases of military land vehicles. A heat exchanger & refrigeration system is used to recover water generated during the combustion process. The system is designed to operate under desert conditions. A mesoscale heat exchanger is under development at MesoSystems, Inc. This unit would be smaller than conventional heat exchangers and could eventually fit in the wheel arch of the HMMWV. The water cleanup is performed using a purification train under development consisting of an ultra-high efficiency glass fiber filter, activated carbon and carbon fiber, zeolites and ion exchange resins. The water purification canister design is challenging since the water contains a mixture of organic and inorganic acidic compounds. Currently, the water meets drinking water standards with a TOC of < 2 ppm and in most cases is less than 0.5 ppm, and a metal's content below EPA regulated limits. Identification and removal of remaining TOC is the focus of current research. For comparison most municipal water supplies have a TOC of 2-3 ppm. The successful development of a system that produces potable water from vehicle exhaust and is small enough to be of military utility will augment a unit's water supply and reduce its dependence on the supply infrastructure. This will lead to a more mobile, deployable, and flexible force. The technology will also provide water to small units in water scarce environments. The system will provide safe, lifesaving, drinking water in disaster relief and emergency applications. It could also provide recreational vehicles in water scarce environments with a critical survival tool... But don't ask Jagtoyen, who can often be seen driving a red Hum-Vee around town, to chug a bottle of her diesel water just yet. There are still traces of two unidentified compounds in the otherwise pure water. They're probably harmless, she said, but so far she's only sipping. ![](exhstwatr.jpg) --- **PATENTS** **US6581375 (B2)** **Apparatus and Method for the Recovery and Purification of Water from the Exhaust Gases of Internal Combustion Engines** Inventor: JAGTOYEN MARIT; KIMBER GEOFFREY M Applicant: LEXINGTON CARBON COMPANY LLC Classification: - international: B01D53/26; C02F1/28; F01N3/00; F01N3/02; F01N3/04; F01N3/28; F01N5/02; C02F1/42; F01N7/02; B01D53/26; C02F1/28; F01N3/00; F01N3/02; F01N3/04; F01N3/28; F01N5/00; C02F1/42; F01N7/00; (IPC1-7): F01N3/00; B01D53/26; B01D53/94; C02F1/28 - European: B01D53/26D; C02F1/28D; F01N3/00B; F01N3/02; F01N3/04B; F01N3/28D; F01N5/02 Also published as: WO02059043 (A3) // WO02059043 (A2-corr) // WO02059043 (A2) // US2002148221 (A1) **Abstract ---** An apparatus and method of use with internal combustion engines, such as used for land vehicles, for the on-board recovery and purification of water. The source of water is from the vehicle's exhaust, where it is collected by condensation. The water recovery system consists of a device for cooling the exhaust so as to condense out the water, such as a counter-current flow heat exchanger in combination with a chiller (a refrigerant-cooled heat exchanger), which cools the exhaust below its dew point. Exhaust condensate is collected at the outlet of the chiller. These cooling devices may be coupled with the vehicle's air conditioning system. The condensed water then flows through the water purification portion of the present invention. The water purification system can rely upon solids filtration and different forms of activated carbons and activated carbon fiber composite materials which can be used in combination with ion exchange resins to provide a water purification train which is integrated with the water recover unit on board the vehicle. The water can be purified to have a TOC of less than 2 ppm to meet EPA drinking water standards, as well as Department of Defense tri-service requirements for long-term consumption as specified in TB Med 577. Potable water can be produced at a rate of approximately up to 0.7 gallons/gallon fuel utilizing a HMMWV diesel engine. This allows production of about 15 gallons per day of potable water on-board the HMMWV (based on consumption of about 30 gallons of fuel per day). **References Cited [Referenced By]** **U.S. Patent Documents** 1653603 December 1927 Schroder 2071868 February 1937 von Lude 2310767 February 1943 Durr 2479766 August 1949 Mulvany 3408289 October 1968 Gustafson 3985648 October 1976 Casolo 4263263 April 1981 Vaseen 4374028 February 1983 Medina 4430226 February 1984 Hegde et al. 4656831 April 1987 Budininkas et al. 4725359 February 1988 Ray 4813632 March 1989 Woodhouse 4863637 September 1989 Matsumoto et al. 5174902 December 1992 Shubert et al. 5256268 October 1993 Goto et al. 5607595 March 1997 Hiasa et al. 5795843 August 1998 Endo 5857324 January 1999 Scappatura et al. 6030698 February 2000 Burchell et al. 6398965 June 2002 Arba et al. **Foreign Patent Documents** WO 00/04977 Feb., 2000 WO **Other References** Jagtoyen, et al., U.S. Army SBIR Contractor's Scientific and Technical Report (Report A002 and A003), "Activated Carbon Fiber Composite for On-board Water Recovery Unit," (SBIR Topic A97090) May 19, 1998.. **Description** **TECHNICAL FIELD** The present invention relates to an apparatus and method for the recovery and purification of water from the exhaust gases of internal combustion engines, such as those used in land transit vehicles, (e.g., cars). More particularly, an on-board, portable device produces potable water from vehicle exhaust gases. **BACKGROUND OF THE INVENTION** Several devices have been utilized over the years to attempt to provide a feasible system for producing potable water from vehicle engine exhaust. These attempts have been generally unsuccessful. Combustion of diesel, kerosene, gasoline, LP gas or other fossil fuels in an internal combustion engine produce water vapor, which is expelled with the exhaust gases. The present invention allows for the recovery of that water to provide a source of water for potable and other uses. The engine exhaust emissions vary as a function of fuel type and composition, as well as the fuel:air ratio, the type of engine and mode of its operation, and also factors such as ignition timing, cylinder design and fuel additives. Although the relative concentrations of various exhaust components may change depending on the mode of engine operation, generally the nature and content of exhaust remains within a predictable range. It would be useful to be able to capture this water vapor and turn it into drinkable water, particularly for military operations or travel in hostile environments (e.g., desert areas). The concentration of water vapor in exhaust gases of either gasoline or diesel engines or turbines ranges up to about 10% by volume. Upon cooling the exhaust gases below its dew point, i.e. about 100.degree. F., water begins to condense. Some gases present in the exhaust, such as oxygen, nitrogen and hydrogen, do not condense. The other exhaust components, such as hydrocarbons, sulfur dioxide, nitrogen oxides, carbon dioxide and particulates and suspended solid matter, other dissolved organic and inorganic matter (including metals), contaminate the condensed water by dissolving in or condensing with the water vapor and must be removed to obtain a potable water product. The treatment apparatus for the recovery of potable water from the engine exhaust must condense the water vapor, remove the particulates, and purify the water produced therefrom. Vehicle exhaust gases and the condensed water produced therefrom are very corrosive. The untreated water that is recovered from the exhaust has a pH of about 3 and, in combination with high temperatures, corrosion easily occurs in pits and crevices of a heat exchanger, ducting and ancillary equipment used to condense it. High exhaust temperatures and the elevated ambient temperatures that prevail under desert/arid conditions exacerbate the rates of chemical attack on materials. Hence, the selection of materials for the components is extremely important. Attempts to recover drinking water from exhaust gases of vehicles have heretofore been unsuccessful because the purification of the water was not considered technically and commercially feasible (i.e., the apparatus was too large, the impurities were too high and/or the process was too expensive). **SUMMARY OF THE INVENTION** In brief, the present invention relates to a method for recovering potable water from the exhaust gases of an internal combustion engine, comprising the steps of: (a) cooling said exhaust gases so as to cause water to condense from said gases (for example, utilizing heat exchangers); (b) passing said water through one or more particulate filters having a maximum pore size of from about 0.1 to about 10 microns; (c) passing said water through one or more activated carbon beds (a preferred one sequentially combining a wood-based carbon having a majority of pores in the range of from about 17 to about 40 .ANG., with a coal-based water-treatment carbon having an average pore size of from about 6 to about 20 .ANG.--the wood-based carbon preferably made by phosphoric acid activation and treated to minimize the amount of phosphorous released into the water); and (d) passing said water through one or more ion exchange resin beds (a preferred one being a mixed bed of highly acidic and strongly basic type 1 ion exchange resins with low organics and particulate contaminants with high cation and anion exchange capacity). Optionally, a buffer such as sodium bicarbonate or a base such as sodium hydroxide may be added to decrease water acidity. The sodium bicarbonate may also improve the taste of the water. These additions may be carried out before either the carbon filtration or the ion exchange resin filtration steps. This system can provide potable water having TOC less than about 0.5 ppm, an inorganic content less than about 2 ppm, and a pH between about 6 and about 8. The potable water can be produced at a rate of at least about 0.5 gallons of water per gallon of engine fuel combusted. The present invention also includes an apparatus for recovering potable water from the exhaust gases of an internal combustion engine comprising a means for connecting said apparatus to the exhaust portal of said engine (preferably via the catalytic converter); a means for cooling the exhaust gases so as to cause the water in said gases to condense; a means for collecting said water and channeling it to a purification system which comprises one or more particulate filters having a maximum pore size of from about 0.1 to about 10 microns, one or more activated carbon beds, and one or more ion exchange resin beds; and means for collecting the water which has passed through said purification system. More specifically, this invention relates to a portable apparatus and the method of recovery and purification of potable water from vehicle exhaust gases. Water can be produced at a rate of at least about 0.5 gallons/gallon of diesel using a 6.5 liter diesel engine with a compression ratio of 21:5:1 and a Brake Mean Effective Pressure (BMEP) of about 300 psi, as is standard issue in a HUMVEE, or "HMMWV" United States armed forces vehicle, while having only a small (i.e. <7%) effect upon the engine performance of the vehicle. A combination of particulate filtration to remove solids, treatment by activated carbon to remove organic compounds and some inorganics, and treatment by ion exchange resin to remove ionic species, provide effective removal of toxic and other contaminants to produce potable water having a purity which exceeds the EPA drinking water standards, as well as the DOD TB MED 577 tri-service water quality standards for long-term consumption. The activated carbon material used in the instant invention removes essentially all of the organic contaminants, even though some are present at concentrations in the ppb range. The water purification step involves passing the water condensed from the exhaust gases having a high concentration of Total Organic Carbon (TOC) materials of from about 50 to about 250 mg/L and a pH of about 2.8, through a particle filter and an activated carbon filter to obtain TOC levels in a range of from about 3 to about 100 mg/L. The resulting product is then passed through an ion exchange resin to remove metals, inorganic, acidic, and remaining organic contaminants. The filtered water samples have a TOC content below detectable limits (BDL) which is 0.5 mg/L for current EPA drinking water regulations and as low as 0.1 mg/L in some instances. This is a significantly lower TOC than a control sample obtained from the local municipal water supply (2.6 mg/L). Moreover, the filtered samples did not contain any of the hazardous organics mentioned in the EPA's drinking water rules. The present invention recovers potable water from engine exhaust by manually or automatically diverting a desired portion of the exhaust gas stream to the water recovery system. The exhaust gas is preferably first passed through the vehicle's catalytic converter. The catalytic converter generally contains catalyst consisting of platinum metals, transition metals or mixtures and oxides deposited either on alumina extrusions or honeycomb-type monolithic supports. The catalytic converter needs to be at a certain temperature to completely oxidize the hydrocarbons present in the exhaust. This normally requires temperatures of from about 700.degree. to about 1200.degree. F. The conditions of the catalytic converter are important to the quality of the produced exhaust condensate. They can significantly affect the amount of particulates and TOC in the condensate. It has been determined that the lifetime of the catalytic converter (for purposes of this invention) is preferably less than about 50,000 miles, more preferably less than about 40,000 miles to produce water with the lowest TOC. Another important factor is the temperature inside the catalytic converter, which depends mainly on the operating conditions of the vehicle. At low speeds or low vehicle engine loads, the temperature in the exhaust is lower than about 500.degree. F., which is not sufficient for the catalytic converter to fully oxidize the hydrocarbons present in the exhaust. It is preferable that the temperature be at least about 500.degree. F., preferably at least about 600.degree. F., or more preferably at least about 700.degree. F. in order to produce exhaust condensates with as low TOC as possible. In order to produce the highest quality drinking water, the exhaust gases are passed through the catalytic converter and vented through a bypass valve when the temperature in the catalytic converter is below the desired operating range. When the temperature of the catalytic converter reaches its operating range, the bypass valve is closed and the treated exhaust gas flows through the catalytic converter to the water collection unit. The first part of the water collection unit is heat exchange. The heat exchangers used in the present invention can be manufactured from aluminum coated with Heresite, stainless steel (SS), inconel, ceramics, or graphite, preferably stainless steel, inconel or ceramic. The initial cooling generally takes place in either an air to gas heat exchanger or a counter-current gas to gas heat exchanger. For the air-gas heat exchange system, the exhaust gas is cooled to about 20.degree. F. above ambient temperature. The exhaust may then be further cooled in an air conditioner cooled condenser. In the most likely application scenario, the ambient "desert" temperature is above the exhaust gas dew-point. Thus, ambient air cooling alone will be insufficient to condense any water at all. A source of cooler heat exchange fluid is required and this is most conveniently provided by refrigerant at 30-80.degree. F., or more preferably 30-50.degree. F., from a typical automotive air-conditioning system. The non-condensable gases from the exhaust are vented and the condensed water is pumped or passed by gravity through a particle filter, activated carbon filer and ion exchange resin column for removal of acidic, metallic, inorganic and remaining organic components and is then sent to a storage tank where it can be disinfected if storage is required for prolonged periods of time. Optionally, a small amount of sodium bicarbonate may be added to the water before carbon or ion exchange filtration. This buffers the water, raising its pH so that it will not attack the filters, particularly the ion exchange resins. It may also improve the taste of the water. Key issues in putting together the water recovery system is the design of a system which fits in a standard vehicle and does not reduce significantly the efficiency of the engine, the removal of particulates and dissolved contaminants which affect taste and odor and can be hazardous to human health, the production of a high enough volume of water to be competitive with alternatives (e.g., carrying a large volume of water), and the ability to work in the high temperature and acidic environment of the exhaust system. The present invention addresses these issues and will be more fully understood from the following detailed description of the invention. **BRIEF DESCRIPTION OF THE DRAWINGS** **FIG. 1** is a schematic of an exemplary water collection phase of the process of the present invention, using an air-gas heat exchanger. ![](a1.jpg) **FIG. 2** is a schematic of a water collection phase of the present invention, using a counter-flow heat exchanger. ![](a2.jpg) **DETAILED DESCRIPTION OF THE INVENTION** The process of the present invention is comprised of two parts: the water collection phase during which the water is condensed from the exhaust gases, and the water purification phase during which particulates, organics and other contaminants are removed in order to make the water potable. In the water collection phase, the hot exhaust gases are cooled causing the water vapor in the exhaust to condense. This may be accomplished by any known cooling mechanism, but is generally done using heat exchangers, cooled by a combination of one or more of the following fluids: ambient air, refrigerant e.g. Freon, or chilled exhaust gas. Prior to entry into the collection phase, the exhaust is preferably passed through the vehicle's catalytic converter to fully oxidize the hydrocarbons in the exhaust to the fullest reasonable extent. In the water purification phase, the water from the collection phase is treated to remove impurities and make the water potable. This generally is accomplished by passing the water through a particle filter, an activated carbon filter, and an ion exchange resin filter. Each of these steps will be described in detail below. **1. Water Collection System** Any condensing means known in the art can be used to collect water from the hot exhaust gases. Two possible exemplary alternative mechanisms will be described for the water condensation system. This does not exclude other systems based on ceramic, graphitic, inconel or other heat exchanger-based systems. **A. Exhaust Condensation by Air-Gas Heat Exchange Combined with Chiller** The estimated average temperature of the exhaust at the tail pipe is normally up to about 800.degree. F. The bulk of the cooling of the exhaust is performed in an air-cooled heat exchanger made either from aluminum coated with Heresite, stainless steel, inconel, titanium, ceramic, mesophase pitch, foam or graphite. The intercooler used in this example is normally used to cool charge air after turbo-compression in large truck engines. The particular intercooler used in these experiments may be obtained, for example, from Thermal Control Technologies Corporation of Prescott, Ariz., but can also be obtained from a range of manufacturers. The intercooler core is 35.5" wide and 30.75" high and has a thickness of 2". It consists of aluminum rectangular section tubing with finned inserts both on the process and service sides. This core is modified to reduce corrosion by coating with Heresite, a commercial process which results in a phenolic resin coating that is only thousandths of an inch thick and has only a minimal effect on heat transfer. Two 16" diameter 12 volt DC fans pull ambient air at up to 6,000 scfm through the intercooler. This heat exchanger cools the exhaust gases down to within about 50.degree. F., and usually within about 20.degree. F., of ambient temperature, which may be below the dew point of the gas. If further cooling is necessary (e.g., in a desert environment), the exhaust gases are further cooled by refrigeration, utilizing the engine-driven compressor from the vehicle's air conditioning system (see below). The water is collected in a container, which may optionally contain a demister to prevent fine aerosol water droplets from escaping with the exhaust air. These components can, for example, be mounted on the rear bed of a HMMVW vehicle. As described above, a chiller, i.e. another heat exchanger, is optionally mounted after the intercooler. One such chiller is a GM Van Rear AC Chiller #1254-3631 which can be installed inside the water collection vessel to save space. The chiller is sealed in the inlet to the vessel so that all exhaust gases must pass the Heresite-coated fins, allowing more cooling of the exhaust gases. The coolant is piped from the front of the vehicle to the rear into the chiller via flexible lines installed under the vehicle along the frame rails and entering the bed of the vehicle through a hole cut into the floor. Optionally, thermal insulation can be added to the chiller vessel. Also optionally, a fan shroud can be added to cover the outlet air side of the intercooler in order to duct the colder air exiting from the second fan down to the hot end of the intercooler. FIG. 1 shows a schematic of an on-board water recovery unit utilizing an air-to-air heat exchanger in combination with a chiller to recover exhaust condensate. In the Figures, T denotes a temperature sensor and P denotes a pressure sensor in the apparatus used to carry out the present invention. These pressure and temperature sensors are used to monitor the process of the present invention on an ongoing basis to optimize its performance. A fan may be used to suck air into the heat exchanger. Moreover, a duct may be placed at a forward or elevated position of the vehicle in order to capture air which has not been subjected to engine heat. **B. Exhaust Condensation by Gas-Gas Counter-Current Flow Heat Exchanger Using Chilled Exhaust as Cooling Medium** An alternative system for water recovery includes a counter-current flow heat exchanger, which uses the chiller-cooled exhaust as cooling medium. This heat exchanger can be manufactured in stainless steel (particularly 304 SS), inconel, titanium, ceramic or graphite. If it utilizes narrow (<1 mm) meso channels and ultra thin walls (<0.1 mm), it may be small enough to install under the vehicle or in a wheel arch because it does not need a supply of cool ambient air (as opposed to the air-gas exchanger described above). This does not preclude the desirability of additional heat loss by locating the exchanger in a cool area or by the use of a small amount of fan-blown ambient air. **FIG. 2** shows a schematic for a water recovery system including a counter-current flow heat exchanger. Refrigerating the exhaust gas already cooled to near ambient temperature and having a relatively high water vapor partial pressure is extremely attractive. For example, cooling the exhaust gases to around 100.degree. F. involves a heat exchange of around 50 kW (e.g., cooling from 600.degree. F. to 100.degree. F.), and possibly no condensation at all if the dew point was 100.degree. F. A further extraction of 5 kW would drop the temperature such that about 15 lbs/hr of water would condense, i.e. a consequent massive increase in the efficiency of the water recovery unit. Moreover, the use of a cooler can reduce the size of the heat exchanger. The compressor and its associated condenser may be shared with the vehicle's air conditioning system or be an independent system. The compressor can be driven by the engine of the vehicle and a switch can be installed to control the compressor and maintain it in the activated position whenever water recovery is desired to be maximized. An important consideration in selecting a heat exchanger is the material of construction. Aluminum is inexpensive but if coated with Heresite should not be used with temperatures exceeding about 450.degree. F. Stainless steel is heavier and more expensive but provides the durable corrosion resistant material desired. Other alternatives include producing a heat exchanger from ceramics; one such example is a unit similar to those used in catalytic converters, although they need to be rendered impermeable. Other possibilities include inconel, titanium or graphitic foams. **2. Water Purification System** The collected water is filtered in several treatment stages, which can be arranged in a purification train. The first stage involves filtration of particulates from the exhaust condensate using material having an appropriate maximum pore size (e.g., from about 0.1 to about 10 microns, preferably from about 2 to about 10 microns), for example, glass fiber paper having a pore size of from about 1 to about 10 microns. Millipore micron filters with 0.1 micron average pore size made, for example, of Teflon.RTM. can also be used. These will have a slower flow rate than the glass fiber paper filters. The second stage involves adsorption of organics and some inorganics onto a bed of activated carbon. The carbon can be either granular activated carbon (GAC), activated carbon fibers, or composites of activated carbon granules and/or activated carbon fibers. Another form of carbon may be a composite or block of activated carbon containing granular or powdered carbon with a binder. Yet another option is to utilize an activated carbon fiber composite containing powdered activated carbon immobilized within the structure. These materials will prevent bed movement during operation. Examples of such carbon materials are disclosed in PCT Published Application No. WO 00/04977, Jagtoyen et al., published Feb. 3, 2000, incorporated herein by reference. The activated carbon adsorbent is an important component of the present invention. The main portion of the acidic compounds and other organic compounds are removed by the activated carbon. "The carbon must have a wide range of pore size distribution; one way to do that is by using two different adsorbent carbons."One carbon is, for example, a coal-based granular activated carbon sold commercially for water treatment. The main porosity is due to pores having an average pore size of from about 6 to about 20 .ANG.. The second carbon bed contains wide pores (mesopores) to remove large organics. This carbon has some narrow micropores in the range of from about 6 to about 12 .ANG., and significant mesoporosity with pores of from about 17 to about 40 .ANG., and some wider mesopores in the about 40-120 .ANG. range. These numbers are based on pore size distribution analysis by N2 adsorption using the Density Functional Theory (DFT). This carbon can be, for example, a wood-based carbon made by phosphoric acid activation. "A carbon found to be useful in the present invention is a Westvaco carbon that was treated so that it does not release too much phosphorus into the water." An alternative would be to use an activated carbon fiber composite for the water treatment instead of the coal-based carbon. This material has an open and permeable structure and can be produced in single pieces to a given size and shape. The activated composite can be made from isotropic pitch-derived carbon fibers and exhibits novel properties including rapid rate of adsorption and desorption, the ability to form specific shapes of high permeability and strength. The open structure of the composites combined with the presentation of the reactive surfaces for adsorption or catalysis in the form of narrow diameter fibers allows direct access of the contacting fluid with minimal mass transfer limitations, and very high rates of adsorption, desorption and reaction. The contaminant removal is better than commercially available filters for many compounds, particularly small organic compounds, and the activated carbon filter also is uniquely effective in that it removes waterborne pathogens with efficiencies of 99.99% or better. This filter is described in PCT Published Application WO 00/04977,Jagtoyen, et al., published Feb. 3, 2000. The carbon filters generally have a minimum surface area of at least about 1000 m.sup.2 /g. Another form of carbon may be a composite or block of activated carbon containing granular or powdered carbon with a binder or resin-based carbons. Yet another option is to utilize an activated carbon fiber composite containing powdered activated carbon immobilized within the structure. There will be no bed movement during operation for the composites, hence no loss of fines, degradation and potential for increased pressure drops in the system over time. Yet another type of carbon can be a surface-treated carbon particularly optimized to remove polar organics from water. In a preferred embodiment, an effective amount of sodium bicarbonate is added to the condensate to counteract its acidity. This may be done at any point in the process but is preferably done prior to the carbon filtration step. The sodium bicarbonate acts to buffer the water and to improve its taste. The third stage is filtration through a bed of ion exchange resin. A mixed bed of cation and anion resins can be used to remove the inorganic contaminants, remaining organic compounds that are polar in nature, acids, nitrates and metals. The ion exchange resin bed removes all the detectable inorganic and metal contaminants to below detectable limits. The resin is preferably a mixed bed of strongly acidic and strongly basic type 1 ion-exchange resins. They are of the ultimate purity in terms of organics leaching and particulate contaminants. A preferred ion exchange resin is Amberlite UP6040.RTM., commercially available from Rohm & Haas. In sample runs, the flow rate through the resin was about 217 ml/min, which is about 42 bed volumes per hour. It is preferred that the flow rate through the water purification system be from about 30 to about 50 bed volumes/hr. A particulate filter is optionally added at the end of the purification train to capture any carbon fines created during filtration. Optionally, the water can be filtered through another activated carbon fiber composite filter. Moreover, the ion exchange resin can be sandwiched between two layers of activated carbon filter composite material utilizing the structural integrity of the composite to support the ion exchange resin to prevent channeling and abrasion forming a monolithic cartridge. Another option is to add a polymeric pre-filter to remove oily compounds. Addition of sodium hydroxide or sodium bicarbonate (or other non-toxic basic salts) before any filtration in order to neutralize the water is a possibility. Zeolites or clays or activated alumina can be used to remove some acids and inorganics. After the purification is complete, the water is stored in a 5-15 gallon container which may or may not contain disinfectants Conventional disinfectants (such as chlorine or mixed oxidants like the MIOX system) can be used at their art-established levels. The water produced by the present invention is potable, satisfying the following maximum impurity levels: TOC of no greater than 2 ppm, and EPA drinking water standards for all organic and inorganic compounds and metals. **EXAMPLES** The following examples illustrate the process and apparatus of the present invention. Exhaust condensate was produced while driving a 1994 civilian-equipped Hummer, modified to practice the present invention, using an intercooler coated with Heresite as heat exchanger in combination with a chiller to condense water from the exhaust. Data from different water production runs are shown in Table 1. The average condensate yield was about 0.5 gallons per gallon of fuel. A large sample of condensate which was produced while driving at 60 mph, and had a TOC of 58.6 mg/L, was used as the raw water for the water purification studies reported below. An example of a water purification train consisted of particulate filters, two different granular carbons and one ion exchange resin filter. The condensate was first filtered through laminated glass fiber paper (maximum pore size 2 micron) which removed on average 55 ppm of solids. A 0.1 micron filter was used for polishing, although this may not be required. Refiltering one batch through a 0.1 micron filter removed less than 0.01 ppm solids. C33 (Coal-based GAC): This bed was made using coal-based activated carbon from the Calgon Corporation. The condensate was run through the column at a flow rate of 20 ml/min or 3.7 column volumes per hour. After 0.7 gallons, the TOC was reduced to 8.1 mg/L. The TOC remained between 7 and 8 mg/L, up to 9.4 gallons. At 10.8 gallons, the TOC increased to 9.9 mg/L. After another 1.4 gallons, the TOC had dropped to 5.3 mg/L and remained low for the rest of the treatment. C34 (Wood-based GAC): After the water was purified through the C33 bed, it was ran through the wood-based GAC bed at 13 ml/min or 2 bed volumes per hour. When this carbon was used after the Calgon carbon (C33), it dropped the TOC down to 3.0 mg/L after 1.3 gallons. When C34 was used after a combination of C33, R11 and R12 (discussed later), the TOC was reduced from 3.2 to 1.5 mg/L after 0.5 gallons and 2.4 mg/L after 0.8 gallons. R11 (Ionac A-554 resin from Sybron Chemicals, Inc.): This resin is designed to remove nitrogen compounds. When used after C33, this resin actually increased the TOC from 5.3 mg/L to 7.4 mg/L after only 1.3 gallons. But when used after C33 and C34, it had no effect on the TOC (the beginning TOC was 3.0 mg/L and the ending TOC was 2.8 mg/L). R12 (Resin from Rohm & Haas): This resin, when used after the carbon filtration (with or without R11), removes the remaining contaminants from the condensate. The column height was 24" and column diameter 1". The flow rate through the bed was 218 ml/min or 42 bed volumes per hour. The optimum flow rate for the resin can range from about 1-50 bed volumes per hour. When R12 was used after the C33-C34 combination, it dropped the TOC from 3.0 mg/L to less than the detection limit of 0.5 mg/L (estimated to be 0.1 mg/L by the instrument). When R12 was used again after the combination of C33C34R12C34, it reduced the TOC to 0.6 mg/L. After the combination of C33C34R11, the TOC was reduced to less than the detection limit of 0.5 mg/L (estimated to be 0.3 mg/L by the instrument). TABLE 1 Water Collection Results Water Amounts (lbs/mile) Yield Dew Calc. Miles Fuel in outlet per gal pt. Dew pt. Temp. Dew pt. Temp. Water Cons actual total - diesel air in exhaust IC out chiller Chiller Run # Collect. (mpg) in fuel air in total in yield yield (gal/gal) (.degree. F.) (.degree. F.) (.degree. F.) out (.degree. F.) out (.degree. F.) Steady 50 mph runs 102 84.9 14.9 0.55 0.06 0.61 0.35 0.26 0.63 29 94 76 61 52 103\* 84.7 15.5 0.53 0.04 0.57 >0.23\* <0.34 >0.44 18 97 75 <80 52 115\* 84.8 14.0 0.59 0.06 0.65 0.31 0.33 0.50 32 99 139 77 75 Steady 60 mph runs 104 146.9 12.5 0.65 0.04 0.69 0.39 0.30 0.59 17 102 86 74 54 105 84.8 12.9 0.64 0.09 0.73 0.36 0.37 0.56 39 102 106 76 80 106 81.4 12.8 0.64 0.05 0.69 0.38 0.31 0.58 25 103 101 78 77 107 84.8 12.9 0.63 0.10 0.73 0.26 0.47 0.41 42 103 93 88 80 108 84.8 13.1 0.63 0.04 0.67 0.34 0.33 0.53 18 102 94 76 76 110 84.8 12.0 0.68 0.03 0.71 0.34 0.37 0.48 13 103 115 83 76 111 84.8 13.4 0.61 0.04 0.65 0.33 0.32 0.54 22 99 105 76 71 113 12.3 12.8 0.64 0.07 0.71 0.44 0.27 0.67 35 103 105 72 79 114 74.9 13.0 0.63 0.06 0.69 0.37 0.32 0.58 29 102 100 78 72 5-50-5 mph runs 109 28.1 10.3 0.79 -- -- 0.50 -- 0.62 31 -- 101 -- 76 116 28.1 10.0 0.82 -- -- 0.43 -- 0.52 27 -- 143 -- 77 \*There were condensed water losses. Good results were achieved by using a combination of the two carbon beds and the Rohm & Haas ion exchange resin column, C33OC34DR12E (referred to as C33E herein). This sample had a TOC of only 0.1 ppm, a pH of 6.8 and conductivity of only 6.1, Table 2. The other sample was purified through both carbon beds and both resin beds, and had a TOC of 0.3 ppm (C33C from now on). It is likely that the second resin bed gave off TOC to the water. The pH of the water is close to neutral at 6.8 and the conductivity is very low, 7.5 .mu.S/cm. There appears to be a correlation between small amounts of TOC and conductivity. Based on these preliminary data, it is believed that conductivity can be used as a sensor for water purity, as well as an indicator of breakthrough on the ion exchange resin bed. TABLE 2 TOC, pH and Conductivity of Drinking Water from Exhaust Exhaust Purified Water Metal Water C33O C33LC34O Contaminant MDL Units W103/115 C34DR12E R11AR12AC3 TOC 0.5 mg/L 65 BDL BDL pH(Lab) 0.1 pH 3.00 6.84 6.81 Conductivity 0.1 .mu.S/cm 496.4 6.14 7.48 The highest purity sample C33E was submitted for trace organics analysis (Chemir Labs, Saint Louis, Mo. and EDG, Lexington, Ky.), to identify the nature of the 0.1 ppm of organic compounds left in the water. ESI MS and GC/MS: The first analytical technique used was Electrospray Ionization Mass Spectrometry (ESI MS) in both the positive and negative ion modes. Positive ion ESI MS produced an ion series consistent with the presence of a small amount of polymer with a separation between the ions of 76 amu. Negative ion ESI did not produce any ions above background. The second technique used was GC/MS, using a solid phase microextractor (SPME) probe to concentrate the analytes before injection. The analysis indicates the presence of toluene (retention time .about.3.2 min) and 2-ethyl-1-hexanol (5.25 min). These compounds are present when the sample analysis is compared to a blank consisting of Millipore purified water. The components are present in very small amounts, and appear to be present in smaller quantities than were observed for the previous analysis. GC/MS Analysis: This resolves the sample components based on volatility, and MS detects and identifies the components. Sample components that interact less with the stationary phase spend less time in the chromatographic column. In MS, the resolved sample components are ionized and separated in a mass analyzer. The fragmentation pattern of a sample component and its computer library match enables sample identification. The organic compounds present in water with TOC of 0.1 and 2.6 ppm are shown in Table 3. TABLE 3 Organic contaminants present in trace amounts in drinking water samples and a sample with 2.6 ppm TOC Contaminants Identified in C33C34R12E C33C34R12E R12E Trace Amounts TOC = 0.1 ppm TOC = 0.1 ppm TOC = 2.6 ppm Toluene trace 0.8 .mu.g/l trace 4-methyl-2-pentanone ND 17 .mu.g/l ND 2-ethyl-1-hexanol trace ND ND small amount of polymer trace ND ND phosphoric acid, alkyl ND ND trace phosphates 2-ethyl-3-hydroxyethylester of ND ND trace 2 methylpropanoic acid Tributyrin ND ND trace Note - TOC limit is 2 ppm for drinking water All metals identified in the exhaust condensate were reduced below regulated levels. Sodium was found at 2 ppm and lithium at 1.2 ppb. Some metals are present in the <1 ppb range, for example, scandium 0.5 ppb, molybdenum 0.13 ppb, niobium 0.01 ppb, aluminum 0.04 ppb, and calcium is present at less than 0.01 ppb. To illustrate the purity of the water from exhaust, a UV-VIS scan was performed on the water along with untreated exhaust condensate, Lexington, Ky. drinking water and organic-free drinking water purchased from an independent laboratory. The UV scans show that the exhaust water contains significantly less organic contaminants than both the organic-free lab grade water and the Lexington drinking water. Specific compositions, methods and embodiments discussed herein are intended to be only illustrative of the invention disclosed by this specification. Variation on these compositions, methods or embodiments are readily apparent to a person of skill in the art based upon the teachings of this specification and are therefore intended to be included as part of the inventions disclosed herein. Reference to documents made in the specification is intended to result in such patents or literature cited are expressly incorporated herein by reference, including any patents or other literature references cited within such documents as if fully set for forth in this specification. The foregoing detailed description is given primarily for clearness of understanding and no unnecessary limitations are to be understood therefrom, for modification will become obvious to those skilled in the art upon reading this disclosure and may be made upon departing from the spirit of the invention and scope of the appended claims. Accordingly, this invention is not intended to be limited by the specific exemplifications presented hereinabove. Rather, what is intended to be covered is within the spirit and scope of the appended claims. --- **USP Appln # 2004231345** **Use of Flow Through Capacitor in the Recovery and Purification of Water from Exhaust Gases of Internal Combustion Engines** 2004-11-25 Inventor: MAZZETTI MARIT JAGTOYEN (US) Classification: - international: B01D5/00; B01D53/26; C02F1/469; C02F9/00; C02F1/18; C02F1/28; C02F1/42; C02F1/44; C02F1/467; B01D5/00; B01D53/26; C02F1/469; C02F9/00; C02F1/18; C02F1/28; C02F1/42; C02F1/44; C02F1/461; (IPC1-7): F17C9/04; F25D3/02; F25D17/06; F25D21/14; - European: B01D5/00H14; B01D53/26D; C02F1/469B; C02F9/00H4 Also published as: US7000409 (B2) **Abstract ---** A process for recovering potable water from the exhaust gases of an internal combustion engine is disclosed. In this process the exhaust gases are cooled causing water to condense out, and the water formed is passed through particulate filters, activated carbon filters and ion exchange resin filters. In this process, the water is treated to reduce the levels of nitrates, sulfates, acidic and other organic components therein (for example, by passing it through a flow through capacitor) before the water is passed through the ion exchange resins. The apparatus for practicing this process is also disclosed. **Description** **TECHNICAL FIELD** [0003] The present invention relates to an apparatus and method for the recovery and purification of water from the exhaust gases of internal combustion engines, such as those used in land transit vehicles. More particularly, an on-board, portable device produces potable water from vehicle exhaust gases. More particularly, the present application deals with the purification of the water formed using a flow through capacitor to assist in the removal of metals, inorganics and TOC. **BACKGROUND OF THE INVENTION** [0004] The present invention allows for the recovery of water from exhaust gases of internal combustion engines, such as those found in military vehicles, cars, jeeps and all-terrain vehicles. The goal is to provide a source of water for drinking and for other uses, for example, for army troops in the field or campers in a wilderness area. The composition of engine exhaust emissions vary as a function of fuel type and content, as well as the fuel:air ratio, the type of engine and mode of its operation, and factors such as ignition timing, cylinder design and fuel additives. Although the relative concentrations of various exhaust components may change depending on the mode of engine operation, generally the nature and content of exhaust remains within a predictable range. It would be useful to be able to capture the water vapor found in engine exhaust and turn it into drinkable water, particularly for military operations or travel in hostile environments (e.g., desert areas). [0005] The concentration of water vapor in exhaust gases of either gasoline or diesel engines or turbines ranges up to about 10% by volume. Upon cooling the exhaust gases below its dew point, i.e., about 100.degree. F., water begins to condense from the exhaust. Some gases present in the exhaust, such as oxygen, nitrogen and hydrogen, do not condense. The other exhaust components, such as hydrocarbons, sulfur dioxide, nitrogen oxides, carbon dioxide and particulates and suspended solid matter, and other dissolved organic and inorganic matter (including metals), contaminate the condensed water by dissolving in or condensing with the water vapor and must be removed to obtain a potable water product. The treatment apparatus for the recovery of potable water from the engine exhaust must condense the water vapor, remove the particulates, and purify the water produced therefrom, and do this in an efficient and effective way. [0006] Vehicle exhaust gases and the condensed water produced therefrom are very corrosive. The untreated water that is recovered from exhaust gases generally has a pH of from about 1 to about 3 and, in a high temperature environment, corrosion easily occurs in pits and crevices of heat exchangers, ducting and ancillary equipment used to condense it, as well as the various materials, such as the ion exchange resins, used to purify the water. High exhaust temperatures and the elevated ambient temperatures that prevail under desert/arid conditions exacerbate the rates of chemical attack on materials. Hence, the selection of appropriate materials for the condensation/purification components can be extremely important. [0007] A method and apparatus for recovering potable water from the exhaust gases of an internal combustion engine is described in our earlier International Patent Application WO 02/059043 A2, published Aug. 1, 2002, and in U.S. Pat. No. 6,581,375, Jagtoyen and Kimber, issued Jun. 24, 2003, both incorporated herein by reference. The method disclosed comprises the steps of: [0008] (a) cooling said exhaust gases so as to cause water to condense from them (for example, utilizing heat exchangers); [0009] (b) passing said water through one or more particulate filters having a maximum pore size of from about 0.1 to about 10 microns; [0010] (c) passing said water through one or more activated carbon beds or monolithic activated carbon (a preferred one sequentially combining a wood-based carbon having a majority of pores in the range of from about 17 to about 40 .ANG., with a coal-based water-treatment carbon having an average pore size of from about 6 to about 20 .ANG.--the wood-based carbon preferably made by phosphoric acid activation and treated to minimize the amount of phosphorous released into the water); and [0011] (d) passing said water through one or more ion exchange resin beds (preferred resins being a mixed bed of highly acidic and strongly basic Type 1 ion exchange resins and/or mixed bed resins exhibiting ultra-low leaching of organics, such as those made for the semiconductor industry, with low organics and particulate contaminants having high cation and anion exchange capacity). The order in which steps (c) and (d) are carried out can also be reversed. [0012] The present invention provides an improvement on the process and apparatus disclosed in that patent application. **SUMMARY OF THE INVENTION** [0013] Specifically, the present invention relates to a method for recovering potable water from the exhaust gases of an internal combustion engine, comprising the steps of: [0014] (a) cooling said exhaust gases so as to cause water to condense from said exhaust gases; followed by [0015] (b) passing said water through one or more particulate filters having a maximum pore size of from about 0.1 to about 10 microns; [0016] (c) passing said water through one or more activated carbon filter beds; and [0017] (d) passing said water through one or more ion exchange resin filters; which includes the improvement comprising, prior to step (d), treating said water (for example, using a flow through capacitor) so as to reduce the levels of nitrates, sulfates, acidic and other organic components therein (for example, so as to reduce the ionic conductivity of said water to from about 1000 to about 20 micro S/cm). [0018] The present invention also relates to an apparatus for recovering potable water from the exhaust gases of an internal combustion engine comprising a means for connecting said apparatus to the exhaust portal of said engine; a means for cooling the exhaust gases so as to cause water in said gases to condense; a means for collecting said water and channeling it to a purification system which comprises one or more particulate filters having an average pore size of from about 0.1 to about 10 microns, one or more activated carbon filter beds, and one or more ion exchange resin beds; and means for collecting the water which has passed through said purification system; and which includes the improvement which comprises the inclusion in said purification system of a means (for example, a flow through capacitor) for reducing the level of nitrates, sulfates, acidic and other organic components in said water prior to passing said water through said one or more ion exchange resin beds. **BRIEF DESCRIPTION OF THE DRAWING** **[0019] FIG. 1** shows the results of the water treatment process described in the Example. ![](b1.jpg) **[0020] FIGS. 2 and 3** show TOC levels from the process described in the Example (samples W371 and W374). ![](b3.jpg) ![](b4.jpg) **DESCRIPTION OF THE INVENTION** [0021] The present invention is an improvement over the process (and apparatus) described in International Patent Application WO 02/059043, published Aug. 1, 2002, and U.S. Pat. No. 6,581,375, Jagtoyen and Kimber, issued Jun. 24, 2003, both incorporated herein by reference. In that process, the exhaust gases from the internal combustion engine are cooled so as to cause the water vapor contained in those gases to condense; the water formed is passed through one or more particulate filters having a maximum pore size of from about 0.1 to about 10 microns; the water is passed through one or more ion exchange resin beds; and the water is passed through one or more activated carbon beds. The water may also, as a final step, be passed through a polishing bed comprising carbon particulate filters. That invention also includes an apparatus for recovery of potable water from exhaust gases of an internal combustion engine comprising a means for connecting said apparatus to the exhaust portal of said engine (preferably via the catalytic converter); a means for cooling the exhaust gases so as to cause the water in those gases to condense; a means for collecting the water and channeling it to a purification system which comprises one or more particulate filters having a maximum pore size of from about 0.1 to about 10 microns, one or more activated carbon beds, and one or more ion exchange resin beds; and means for collecting the water which has passed through said purification system. [0022] In the present improvement, the acidic and ionic components, such as sulfates and nitrates, as well as metals and organics, are removed from the condensed water prior to the time that the water is introduced into the ion exchange resins. It was found that the presence of sulfates and nitrates in the untreated condensate was causing problems over time. Specifically, the corrosive nature of the untreated exhaust condensate caused oxidation and degradation of the ion exchange resins and other components of the purification system, with a resulting leaching of organic compounds from the ion exchange resin into the treated water. In the process of the present invention, ionic components, such as sulfates and nitrates, are removed from the condensed water. The process may also remove acidic and polar organic compounds. The net result of this removal is that the ionic conductivity of the condensed water is reduced from about 700-1000 micro S/cm to about 10-50 micro S/cm. It is preferred that the treated condensed water have an ionic conductivity of from about 10 to about 80, more preferably from about 10 to about 50, most preferably from about 10 to about 30, micro S/cm. [0023] One way of accomplishing the removal of these ionic compounds is through the use of a flow through capacitor (FTC). Flow through capacitors are known in the art and are commercially available from Biosource Inc. They are described, for example, in the following U.S. patents, which are all incorporated herein by reference: U.S. Pat. Nos. 5,192,432, Andelman, issued Mar. 9, 1993; 5,196,115, Andelman, issued Mar. 23, 1993; 5,200,068, Andelman, issued Apr. 6, 1993; and 5,360,540, Andelman, issued Nov. 1, 1994. Generally, the flow rate through the capacitor will be from about 0.1 to about 2 lpm (preferably about 500 ml/min), the current in the capacitor is from about 7 to about 11 A, and the voltage is between about 1.2 and about 1.5 V. [0024] Another technology that may be useful in treatment of the condensate is electrochemical treatment where a voltage of 12-18 V at 2-4 A is applied to electrodes immersed in the water (i.e., an electrochemical cell). Powerful oxidizing agents are produced without the addition of chemicals. Most kinds of organic contaminants present in aqueous effluents are destroyed or oxidatively degraded. BOD, COD, TOC, odor, color, microorganisms, or other parameters indicative of the presence of organic contaminants can be reduced to the ppb level or lower. [0025] Reverse osmosis, a process well known in the art, may also be used to treat the condensate. [0026] The removal of acidic and ionic components from the condensate will render the water less corrosive before it enters the ion exchange resin bed. By removing the sulfates, nitrates and organic acids prior to running it through the ion exchange resin bed, corrosion to the bed will be minimized. An additional benefit of this process is the potential to remove ionic contaminants from surface waters and sea water, allowing the use of these as alternative water sources for the purification system disclosed herein. **EXAMPLE** [0027] The following example illustrates the process and apparatus of the present invention. [0028] The internal combustion engine exhaust utilized in this example was produced while driving a 1994 civilian-equipped Hummer, modified to practice the present invention, which included a heat exchanger to condense the water from the exhaust gases (manufactured by NSM Corporation, England). The water purification train of the present invention consisted of particulate filters, a flow through capacitor, two different granular carbon filters and one ion exchange resin filter. [0029] The condensate was first filtered through laminated glass fiber paper (maximum pore size 2 microns), which acted as a particulate filter, removing an average of 55 ppm of solids. The glass fiber paper was manufactured by Hollingsworth and Vose. [0030] The condensate was carbon-treated prior to introduction into the flow through capacitor (FTC) to remove neutral organics that can foul the membranes and electrodes of the FTC. The carbon filter materials utilized were selected based on two main criteria: high hardness and wide pore size distribution. In this example, two different carbons were used. The first was coal-based carbon F300 from Calgon, which has high hardness and high density and, as a result, exhibits high capacity for organic removal from water. The second carbon utilized has a relatively wide pore size distribution and is a wood-based carbon, such as RGC from Westvaco. This carbon is used to remove large molecular weight organics as well as some polar organics that coal-based carbons with less functionality do not remove as well. The carbon materials were packed sequentially in a 2-inch diameter, 10-inch tall SS bed operating in an up-flow mode. The flow rate through the bed was 22 ml/min, which is equivalent to about 150-200 ml/min in a full size bed (which would be able to treat more than 2 gallons of water/hour). The results of the carbon treatment are shown in Tables 1 and 2 and FIG. 1. The TOC of the condensate water is lowered by this procedure from a starting TOC of about 50-80 ppm to below about 20-30 ppm, i.e., most of the nonpolar organics and some polar organics are removed. 1TABLE 1 TOC at different stages of treatment for condensates W177/78 W177/78 A B C Untreated 67.52 67.52 67.52 Carbon 9.53 11.48 12.34 Capacitor pure 7.75 10.41 11.81 Capacitor waste 8.03 11.9 12.46 R1 -- 3.85 R2 2.61 1.07 Carbon 0.82 0.23 R1: WA-30 Mitsubishi R2: SMT200L, Mitsubishi [0031] 2TABLE 2 TOC at different stages of treatment for condensate W185 Waste W185 A B C D E F AC Untreated 54.44 54.44 54.44 54.44 54.44 54.44 Carbon 9.38 10.64 14.12 14.49 20.03 21.89 Capacitor pure 9.01 9.58 10.4 13.42 8.98 Capacitor waste 9.58 10.92 14.22 24.97 12.42 R1 6.56 9.12 9.41 9.04 10.51 9.12 R2 3.44 6.836 6.96 Carbon 1.61 3.844 5.93 R1: WA-30, Mitsubishi R2: SMT200L, Mitsubishi [0032] A flow through capacitor (FTC), produced by Biosource, Inc., was used in this example. The flow through capacitor consists of two electrodes: one positive and one negative. Charged compounds are absorbed on the electrodes, and when the capacitor has reached saturation it is discharged. The absorbed ions are desorbed and form a waste stream that is discarded. For this application, the capacitor should be optimized to have a waste stream that comprises less than about 5% of the water treated. The FTC can remove impurities like metals and sulfates and nitrates from water by flowing it over a charged electrode. The capacitor will remove and hold contaminants from influent condensate when it is appropriately charged. The effluent condensate is thereby purified. At some point during the process, depending upon the flow rate and quality of the incoming stream, the FTC will saturate with impurities and become ineffective. The impurities must then be discharged in a separate effluent waste stream by turning off the surface charge. The polarity of each electrode can be reversed every cycle to prevent fouling of the electrode. A preferred FTC unit is one which is self-regulating for time on line and time for regeneration of the electrodes in order to obtain water of a predefined purity. [0033] In this example, Sample W174, exhaust condensate from a titanium cross-flow heat exchanger, was treated with the Biosource FTC. Because of potential problems with TOC accumulating on the capacitor electrode, this condensate was treated with carbon (as described above), before it was run through the capacitor. The total condensate volume treated for W174 was about 3 gallons. The TOC concentration in the purified water after different treatment stages is shown in FIG. 1. The TOC of the condensate before carbon treatment was 49 ppm. The carbon treatment reduces the TOC to 18-34 ppm, by removing all nonpolar and some of the polar organics. [0034] The next stage is treatment with the Biosource FTC to remove nitrates, sulfates, metals, inorganics and polar organics. This was achieved by rejecting a waste stream rich in the polar contaminants. The water was flowed through the capacitor at a flow rate of about 350 ml/min, the voltage was about 40 V, and the current varied between about 1 and about 40 amps. The yield of purified water was 92% in this experiment, i.e., about 8% of the water enriched in contaminants was rejected. [0035] The water was resin treated and carbon treated again at the end to remove any organics leaching from the ion exchange resin bed. A 1-micron filter was used at the end to filter out any fines created during the filtration process. The TOC of the final sample ranged from 0.6-2.9 ppm after 3 gallons of condensate was purified with polishing beds of carbon and resin (see FIG. 1). By using the capacitor, the water yield was reduced by 8%, but the size of the water purification canisters in the apparatus will also be reduced significantly, and the problem of dissolution of the binder in the ion exchange resin is avoided as a result of removing the sulfates and nitrates at an early stage in the process. [0036] A second capacitor with Teflon.RTM. membranes (Biosource, Inc.) was tested to determine if it was more resistant to the acidic environment of the exhaust condensate (flow rate.apprxeq.300 ml/min; capacitor charge=7-10 A and 1.2 V). Water condensate samples W177 and W185 were both treated in this capacitor. The TOC of the starting condensate and the purified water are shown in Tables 1 and 2. A total of 2.5 gallons of W177 were treated. For sample W185, 3 gallons were treated. The TOC content of the water was not reduced significantly, only 1-2 ppm, using this cell (see Tables 1 and 2), suggesting that the earlier data where TOC was lowered could be partially due to retention on the cell, or that the operation of the cell was such that it was not in balance, i.e., too little time was allowed for regeneration so that TOC was accumulating at the electrodes. [0037] The capacitor removed the nitrates, sulfates and metals to below detectable limits (BDL), as can be seen in Table 3. The nitrate and sulfate content of the raw condensate was 0.6 and 72 ppm, respectively, and after treatment with the capacitor the nitrates were below 0.02 ppm and sulfates were below 0.2 ppm. All metals were removed to BDL, except for trace levels of sodium, silica, iron and calcium, none of which are hazardous and all of which would be removed by the ion exchange resin downstream. Since the capacitor is so efficient in removing the inorganics and metals, the size of the ion exchange resin bed can be significantly reduced. 3TABLE 3 Metal Content of Cendensates treated by Carbon and Flow Through Capacitor (FTC) Raw Condensate Carbon & Capacitor Parameter MRL MCL W177/78 W177C2P1 W177C3P1 W177C4P1 Units Method Metals Antimony 1 6 <1.0 <1.0 <1.0 <1.0 .mu.g/L 200.8 Arsenic 2 10 <2.0 <2.0 <2.0 <2.0 .mu.g/L 200.8 Barium 2 2000 38 <200 <200 <200 .mu.g/L 200.8 Beryllium 0.3 4 <0.3 <10 <10 <10 .mu.g/L 200.8 Cadmium 1 5 <1.0 <10 <10 <10 .mu.g/L 200.8 Lead 1 15 2 <1.0 <1.0 <1.0 .mu.g/L 200.8 Nickel 1 100 240 <40 <40 <40 .mu.g/L 200.8 Selenium 2 50 <2.0 <2.0 <2.0 <2.0 .mu.g/L 200.8 Thallium 0.4 2 <0.4 <100 <100 <100 .mu.g/L 200.8 Aluminum 2 50-200 8500 <200 <200 <200 .mu.g/L 200.8 Boron 5- 850 <10 <10 80 .mu.g/L 200.8 Calcium 0.1- 0.05 0.05 0.05 mg/L 3111B Cobalt 2- <2.0 <50 <50 <50 .mu.g/L 200.8 Copper 1 1000 37 <20 <20 <20 .mu.g/L 200.8 Iron 0.1 0.3 0.014 0.008 0.006 mg/L 3111B Magnesium 0.05- 0.2 <10 <10 <10 mg/L 3111B Manganese 2 50 33 <5 <5 <5 .mu.g/L 200.8 Molybdenum 2- 13 <200 <200 <200 .mu.g/L 200.8 Potassium 0.05- <40 <40 <40 mg/L 3111B Silica 0.2- 0.74 1.1 0.7 mg/L 200.7 Silver 2 100 <2.5 <20 <20 <20 .mu.g/L 200.8 Sodium 0.29 0.28 1.09 mg/L Titanium 5- <5.0 <5.0 <5.0 <5.0 .mu.g/L 200.8 Vanadium 2- <2.0 <200 <200 <200 .mu.g/L 200.8 Zinc 5 5000 350 <10 <10 <10 .mu.g/L 200.8 Inorganics Nitrate 0.1 0.6 <0.02 <0.02 <0.02 mg/L 300 Sulfate 0.1 72 <0.2 <0.2 <0.2 mg/L 300 TOC 0.5 2 67.52 7.73 10.2 11.81 ppm Lexcarb Conductivity 20 25 50 microS/cm Solids 0.5 ppm Lexcarb pH 3.1 5.4 [0038] Jet fuel, such as JP8, may be used as a fuel in the HMMWV engine. The resulting condensate is more acidic that condensates made from commercial diesel fuel with pH ranging from 1.7-2.3 for JP8, and 2-2.3 for diesel. This is due to the higher sulfur content in JP8. The sulfur content of JP8 fuel can be as high as 3000 ppm, while in diesel it is about 500 ppm. In the examples given below, the sulfur content was 1620 ppm resulting in a condensate pH of 1.7-2.3. The high acidity does affect ion exchange resin performance. The resin performance is degraded due to the acidic condensate resulting in higher TOCs than previously seen in the purified water. [0039] Based on previous data, a flow through capacitor was designed for exhaust condensate purification. This capacitor was optimized to only deliver high quality water of a certain conductivity (in the range 20-80 micro S/cm) while maintaining a high yield of purified water. The results from water purification studies with JP8 fuel have been excellent when using the capacitor as part of the water purification. [0040] Two different exhaust condensates (W371 and W374) were purified with the resin/carbon filtration system, described above and in U.S. Pat. No. 6,481,375. In separate runs, the same condensates were pretreated with the capacitor prior to the resin/carbon treatment. The data from the capacitor runs are shown in FIGS. 2 and 3, and the results of the water purification study in Table 4. 4 TABLE 4 TOC (ppm) Purification Stage W371 W374 W371 Condensate 28.7 18.9 28.7 Carbon treated 12.22 9.61 -- Capacitor treated 4.3 2.33 -- Resin/Carbon purified water 75 gallon 0.65 0.75 1.3 treated **Description of Capacitor Operation** [0041] The basic operation of the capacitor in the present invention is as follows. The capacitor cycling starts with a change in polarity where water is pumped into the spacer. Then the concentration cycle starts and lasts for 150 seconds where polar compounds are migrating toward the electrode. The current starts out at about 30 A and drops to about 5 A during the concentration cycle. The voltage stays constant at 1.2 V. The pump comes on and diverts high conductivity waste to the waste tube and then the polarity is reversed and the pure water starts flowing as soon as it meets the required conductivity level. [0042] Purification cycle: current=6-10 A; voltage=1.2 V [0043] Concentration cycle: current=30 A drops to 5 A; voltage=1.2 V [0044] Waste cycle: current=6-10 A; voltage=1.2 V [0045] In structuring the capacitor cell for use in the present invention, the waste water can be recycled for purification in order to obtain total water yields of 90-95%. A conductivity probe can be used to monitor conductivity in the incoming stream, the purified stream and the waste stream, and the waste can be rejected only when it exceeds a defined limit set to achieve purification yields of 95% or greater. In this way, only water that meets a certain conductivity standard would be allowed to pass through to the next purification step. After treatment of a particular sample by the capacitor, that sample had a conductivity of 30-50 microS/cm. The pH of the sample was still around 5-6, suggesting that there were still acidic organics in the water since all the nitrates and sulfates had been removed. In that case, the condensate was treated with a base ion exchange resin, for example UP 4000 from Rohm and Haas, before treatment with the high purity, low TOC leaching resin, in this case UP 6040, from Rohm and Haas (SMT 2001 from Mitsubishi gives similar results). The condensate may then be carbon treated. The final TOC content of the samples varied from 0.2 ppm to as high as 5 ppm. --- Carbon fiber filters US2004040906 2004-03-04 Carbon fiber filters US2003136728 2003-07-24 Carbon fiber filters for air filtration US2003089237 2003-05-15 Carbon fiber filters ZA200004369 2002-04-29 CARBON FIBER FILTERS NO20004071 2000-08-14 COMBINED MAGNETITE AND ACTIVATED CARBON FILTERS FOR PURIFYING A FLUID STREAM WO0064578 2000-11-02 DEVICE AND SYSTEM FOR MONITORING INTERNAL TEMPERATURE OF INACCESSIBLE OR MOVING PARTS PL351382 2003-04-07 Activated carbon fiber composite material and method of making US6258300 2001-07-10 Activated carbon and process for making same US6057262 2000-05-02 Method for producing catalysts from coal DE19739214 1998-04-02 Activated carbon fiber composite material and method of making US6030698 2000-02-29 ---